Deuterium lamp for Hitachi and Primaide detectors, flanged base with a flying lead and spade terminals.

This is an aftermarket part, not an original manufacturer part. Instrument names and part numbers identify what it fits and replaces; they remain the trademarks of their owners. The manufacturer, country of origin, rated life and warranty are stated in the quote, before you decide anything. If you need the OEM part, say so and I will quote that instead.

Detector lamps and light sources

Deuterium lamp for Primaide VWD

Replaces OEM part numbers: 2J1-1500, 891-2733, 239-0354

Deuterium lamp for the Primaide variable wavelength detector, cross-referenced to 2J1-1500, 891-2733 and 239-0354. The Primaide VWD and the Primaide DAD do not take the same lamp, and the system badge is identical, so confirm which detector module you have before ordering. If your chromatogram is a single trace at one wavelength you are on the VWD; if you can extract spectra from a run, you are on the DAD and you want the other part.

Type: Deuterium
Fits: Primaide VWD
Replaces: 2J1-1500, 891-2733, 239-0354
RFID chip: No
Condition: new
Price: CA$1,064 before tax and shipping. Confirmed on the quote.

Request a quote +1 437-505-5995

This lamp has no RFID chip. Some detectors read a chip to log lamp hours. On those, an untagged lamp reports a tag error and will not ignite until you set the lamp type manually, and you reset the lamp-hours counter yourself afterwards. It runs normally once that is done. What that involves. If you would rather have the chipped version, say so and I will quote that instead.

Before you order: if the instrument is misbehaving, tell me the symptom, not the part number. Lamps and seals get replaced for problems they did not cause. The first look costs nothing, and if this part is not the fix, I will say so.

How buying works, written for procurement →

More for Primaide and similar systems

Detector lamps and light sources

Deuterium lamp for Primaide DAD

Deuterium lamp for the Primaide diode array, cross-referenced to 2J1-1500 and 893-4755. The DAD and the VWD carry the same brand name and different lamps, so identify the module rather than the system before ordering. The advantage of being on a DAD is diagnostic: plot the full spectrum of a blank injection and lamp ageing shows itself as noise concentrated below 250 nm. Flat noise across the whole range is something else, usually the flow cell.

Type: Deuterium
Fits: Primaide DAD
Replaces: 2J1-1500, 893-4755
RFID chip: No

CA$1,064

Enquire

Request a quote

Deuterium lamp for Waters detectors, flanged base with a flying lead and a keyed connector.

Detector lamps and light sources

Deuterium lamp for Waters 2489 and 2998 detectors

Aftermarket deuterium lamp for the Waters 2489 and 2998, cross-referenced to 201000281. The 2489 runs at set wavelengths and the 2998 reads the full spectrum, and the same lamp serves both. On either detector, deuterium output falls fastest in the deep UV, so a method running at 210 nm loses sensitivity long before one running at 254 nm does. This detector expects a lamp carrying an RFID tag. The chip is listed in the specification above, and it is worth confirming before you order, because a chipless lamp can be refused by the instrument.

Type: Deuterium
Fits: Waters 2489, 2998
Replaces: 201000281, 201000273
RFID chip: Yes

Price on request

Enquire

Request a quote

Detector lamps and light sources

Deuterium lamp for Waters 996 and 2996 PDA detectors

Deuterium lamp for the Waters 996 and 2996 photodiode array, cross-referenced to WAT052586. A PDA reads the whole spectrum at once, which is what makes lamp ageing visible earlier here than on a fixed wavelength detector: pull up a 3D plot and you can watch the deep UV end go noisy while 254 nm still looks fine. Use that before ordering. If the noise is flat across the whole spectrum rather than worst below 250 nm, the lamp is not what is wrong.

Type: Deuterium
Fits: Waters 996, 2996
Replaces: WAT052586
RFID chip: No

CA$1,062

Enquire

Request a quote

Detector lamps and light sources

Power supply for Waters 2489 HB lamp

Power supply for the Waters 2489 high brightness lamp, cross-referenced to 700002785. This is the part to consider when a new lamp has not fixed the fault. The high brightness lamp needs its supply to strike and hold it, and a failing supply gives you a lamp that will not light, or one that lights and then goes unstable, both of which look identical to a dead lamp from the front panel. If you have already fitted a new lamp and nothing changed, order this rather than a second lamp.

Type: Power supply
Fits: Waters 2489
Replaces: 700002785

Price on request

Enquire

Request a quote