Skip to main content

Independent. Diagnosis first, parts second.

+1 437-505-5995 [email protected]

Chromkit
Get a quote
Illustration of a detector lamp. Generic drawing, not a photograph of this part. Illustration

This is an aftermarket part, not an original manufacturer part. Instrument names and part numbers identify what it fits and replaces; they remain the trademarks of their owners. The manufacturer, country of origin, rated life and warranty are stated in the quote, before you decide anything. If you need the OEM part, say so and I will quote that instead.

Detector lamps and light sources

Lamp for PerkinElmer Series 200 UV/Vis

Replaces OEM part number: B0114620

Lamp for the PerkinElmer Series 200 UV/Vis, cross-referenced to B0114620. This is the second of the two numbers that appear against this detector; the other is N2900484. They are not interchangeable, and the instrument badge will not tell you which you have, so the number printed on the lamp being removed is the thing to go by. Send me a photograph of the old label if it is hard to read and I will confirm the part before quoting anything.

Type
Detector lamp
Fits
PerkinElmer Series 200 UV/Vis
Replaces
B0114620
RFID chip
No
Condition
new
Price
Quoted per order, in Canadian dollars
Request a quote +1 437-505-5995

This lamp has no RFID chip. Some detectors read a chip to log lamp hours. On those, an untagged lamp reports a tag error and will not ignite until you set the lamp type manually, and you reset the lamp-hours counter yourself afterwards. It runs normally once that is done. What that involves. If you would rather have the chipped version, say so and I will quote that instead.

Before you order: if the instrument is misbehaving, tell me the symptom, not the part number. Lamps and seals get replaced for problems they did not cause. The first look costs nothing, and if this part is not the fix, I will say so.

How buying works, written for procurement →

More for PerkinElmer and similar systems

Illustration of a detector lamp. Generic drawing, not a photograph of this part. Illustration

Detector lamps and light sources

Deuterium lamp for PerkinElmer Series 200 UV/Vis

Deuterium lamp for the PerkinElmer Series 200 UV/Vis detector, cross-referenced to N2900484. A second part number, B0114620, also appears against this detector, so read the label on the lamp you are removing rather than ordering by the instrument name. The Series 200 is an older modular stack and many are still in service, which means the flow cell has usually had a longer life than the lamp. Clean it and re-run your baseline before deciding the lamp is finished.

Type
Deuterium
Fits
PerkinElmer Series 200 UV/Vis
Replaces
N2900484

Price on request

Enquire

Request a quote
Illustration of a detector lamp. Generic drawing, not a photograph of this part. Illustration

Spectrophotometer and AAS lamps

Deuterium lamp for PerkinElmer Lambda series

Deuterium lamp for the PerkinElmer Lambda series, cross-referenced to L6022728. The Lambda range spans a lot of instruments and several generations, so the series name on the badge is not enough to order from. Read the number printed on the lamp that is fitted, or send me a photograph of the housing. Deuterium output falls first in the deep UV, so if your problem sits below about 250 nm the lamp is a fair suspect, and if it covers the whole scan it is not.

Type
Deuterium
Fits
PerkinElmer Lambda series
Replaces
L6022728
RFID chip
No

CA$1,329

Enquire

Request a quote
Deuterium lamp for Waters detectors, flanged base with a flying lead and a keyed connector.

Detector lamps and light sources

Deuterium lamp for Waters 2489 and 2998 detectors

Aftermarket deuterium lamp for the Waters 2489 and 2998, cross-referenced to 201000281. The 2489 runs at set wavelengths and the 2998 reads the full spectrum, and the same lamp serves both. On either detector, deuterium output falls fastest in the deep UV, so a method running at 210 nm loses sensitivity long before one running at 254 nm does. This detector expects a lamp carrying an RFID tag. The chip is listed in the specification above, and it is worth confirming before you order, because a chipless lamp can be refused by the instrument.

Type
Deuterium
Fits
Waters 2489, 2998
Replaces
201000281, 201000273
RFID chip
Yes

Price on request

Enquire

Request a quote
Deuterium lamp for Waters detectors, flanged base with a flying lead and a keyed connector.

Detector lamps and light sources

Deuterium lamp for Waters 996 and 2996 PDA detectors

Deuterium lamp for the Waters 996 and 2996 photodiode array, cross-referenced to WAT052586. A PDA reads the whole spectrum at once, which is what makes lamp ageing visible earlier here than on a fixed wavelength detector: pull up a 3D plot and you can watch the deep UV end go noisy while 254 nm still looks fine. Use that before ordering. If the noise is flat across the whole spectrum rather than worst below 250 nm, the lamp is not what is wrong.

Type
Deuterium
Fits
Waters 996, 2996
Replaces
WAT052586
RFID chip
No

CA$1,062

Enquire

Request a quote