Illustration

This is an aftermarket part, not an original manufacturer part. Instrument names and part numbers identify what it fits and replaces; they remain the trademarks of their owners. The manufacturer, country of origin, rated life and warranty are stated in the quote, before you decide anything. If you need the OEM part, say so and I will quote that instead.

Spectrophotometer and AAS lamps

Tungsten lamp for Analytik Jena SPECORD 50, 200, 210 and 250 PLUS

Replaces OEM part number: 820-60267-P

Tungsten halogen lamp for the SPECORD 50, 200, 210 and 250 PLUS, cross-referenced to 820-60267-P. The tungsten source covers the visible range, so its ageing shows up where the deuterium lamp's does not: rising noise above roughly 350 nm while the UV end stays clean. Tungsten lamps usually dim gradually rather than failing outright, so a slow loss of photometric accuracy in the visible is the thing to watch. Change it before an audit rather than after, since it is the cheaper of the two sources.

Check this before you order

This is the visible-range lamp. If the fault is in the ultraviolet, below about 340 nm, you need the deuterium lamp instead. A SPECORD has both.

Type: Tungsten halogen
Fits: Analytik Jena SPECORD 50, 200, 210, 250 PLUS
Replaces: 820-60267-P
Condition: new
Price: Quoted per order, in Canadian dollars

Request a quote +1 647-919-3041

Before you order: if the instrument is misbehaving, tell me the symptom, not the part number. Lamps and seals get replaced for problems they did not cause. The first look costs nothing, and if this part is not the fix, I will say so.

How buying works, written for procurement →

More for SPECORD and similar systems

Illustration

Spectrophotometer and AAS lamps

Deuterium lamp for SPECORD PLUS

Deuterium lamp for the SPECORD PLUS, cross-referenced to 820-60274-C. Analytik Jena benches carry a deuterium source for the UV and a separate tungsten source for the visible, and the two fail differently. If the noise sits below the changeover wavelength the deuterium lamp is the suspect; above it, the tungsten. Note the number on the lamp fitted before ordering, because the SPECORD family covers several generations and the part is not common to all of them.

Type: Deuterium
Fits: Analytik Jena SPECORD PLUS
Replaces: 820-60274-C
RFID chip: No

CA$1,805

Enquire

Request a quote

Illustration

Spectrophotometer and AAS lamps

Deuterium lamp for SPECORD 2xx, 50, 40, 30, S600, S100 and SPEKOL 1200

Aftermarket deuterium lamp for the Analytik Jena SPECORD 2xx (PLUS), 50 (PLUS), 40, 30, S600, S100, SPEKOL 1200, cross-referenced to 820-60021-0. A benchtop spectrophotometer carries two lamps, deuterium for the UV and tungsten for the visible. The wavelength where the problem appears tells you which of the two to change.

Type: Deuterium
Fits: Analytik Jena SPECORD 2xx (PLUS), 50 (PLUS), 40, 30, S600, S100, SPEKOL 1200
Replaces: 820-60021-0
RFID chip: No

CA$1,805

Enquire

Request a quote

Deuterium lamp for Shimadzu detectors and spectrophotometers, flanged base with a flying lead and a keyed connector.

Spectrophotometer and AAS lamps

Deuterium lamp for Shimadzu UV-Vis spectrophotometers

Deuterium lamp for the Shimadzu UV-Vis bench, cross-referenced to 062-65055-05. These are double beam instruments, which hides lamp ageing for longer than a single beam does: the reference beam absorbs some of the drift, so by the time the baseline looks wrong the lamp is usually well past its useful output. The tell is noise creeping up below 250 nm while the visible range still looks clean. Run the instrument's own energy or lamp history check before ordering, and if the noise covers the whole scan the lamp is not your problem.

Type: Deuterium
Fits: Shimadzu UV-3700, 3600, 2700, 2600, 2550, 2450, 1700, 1800, 1240, 1280
Replaces: 062-65055-05
RFID chip: No

Price on request

Enquire

Request a quote

Illustration

Spectrophotometer and AAS lamps

Deuterium lamp for Shimadzu UV-1800 and UV-1900

Deuterium lamp for the UV-1800 and UV-1900, cross-referenced to L6302-40. These benches keep a lamp hour counter, and it is worth reading before you diagnose anything, because a lamp left on continuously accumulates hours far faster than the number of samples suggests. Many labs never switch the source off between runs. If the counter is low and the UV end is still noisy, suspect a dirty cuvette or a fouled window before the lamp. Reset the counter after fitting, or the next person inherits a number that means nothing.

Type: Deuterium
Fits: Shimadzu UV-1800, UV-1900
Replaces: L6302-40

Price on request

Enquire

Request a quote